• 목록
• 답변
• 게시판 리스트 옵션
  • 수정
  • 삭제

What to Do If Your Key Won't Turn in the Ignition

If you find that your key has become stuck in the ignition or that it doesn't start the engine, it could be a sign that the ignition switch or key cylinder needs replacing. This is a complicated job that requires specific tools.

After installing the new switch, connect the battery and test it by turning the key to the On position.

Identifying the Issue

A key that doesn't turn when you turn the ignition is not just an inconvenience, but can also prevent you from getting your car started. You can try to fix the problem yourself before calling an emergency repair service.

The first step is to make sure that the key is not inserted in the wrong manner. It may seem strange that a key that fits in the lock at one end won't turn if it is inserted into the other. But it is common that drivers insert the wrong key into the correct cylinder. This is why having a spare or emergency key is an excellent idea. It can help you avoid this type of situation and help you get back on the road quickly.

Check the ignition and key for any debris or dirt which may be causing problems. Aggressive turning can cause the pins within the ignition lock cylinder to misalign and that is why it is so important to be gentle when you are trying to start the engine.

If wiggling the ignition key isn't helping, you can use a small tack-hammer to tap the cylinder lightly to loosen the springs and pins. This technique works because tapping the cylinder creates vibrations that stimulate the springs to move, which in turn will allow the key to turn. Be aware that when you apply too much force you could break the cylinder of ignition as well as the key.

You can also try lubricating both the key and the cylinder with an oil that penetrates. This will help in the event that the key becomes stuck due to a accumulation of grime, since it will break loose and move around freely once the mechanism is lubricated.

If none of these solutions work, you should call an auto repair service. The locks and cylinders in these vehicles are prone to wear and tear particularly if they are frequented and a key that won't turn can be an indication that it's time to replace it.

Preparing for the replacement

Many people believe that if they encounter problems with their vehicle, the first thing to do is contact the dealer. Many people are unaware that locksmiths or garages run by independent garages can fix their problems at a lower cost than dealers. In fact, if your key won't go into the ignition it could be a sign your ignition cylinder is starting to fail, and it's time to replace it.

You'll need a few things done prior to starting the replacement process. First, you'll need to locate a safe location to work. Be sure to stay away from traffic and the parking brake is in use. Also, you'll need to disconnect the negative battery cable to avoid activation of electrical systems while you're working.

The next step is to remove any steering column or dashboard covers that block easy access to the ignition. This will let you perform the task faster and lessen the risk of damaging your vehicle's components. Before you begin, ensure that you have all the tools you need. The more precise the tools you have, the easier it is to complete the job correctly.

Once you have the equipment you need, it's time to begin preparing for the ignition cylinder replacement. You'll need to look over the ignition cylinder and see whether it is repairable by simply replacing or smoothing out the wafers within. If the cylinder's in broken beyond repair, then you'll need to have a new one cut by an expert locksmith.

If the ignition cylinder is in good shape and you are able to try to fix ignition switch the issue by using a chisel or flathead screwdriver to wiggle into the keyway, then turn it until it is released. Be careful not to apply excessive force as this can cause more damage than it fixes. If this method isn't working, then it may be necessary to drive your tool deeper into the cylinder to create more torque and leverage.

Removing the Ignition Cylinder

The ignition lock cylinder is the place where you insert your keys into your vehicle to start it and turn on its engines, or turn on other systems, like your radio. It is housed inside the ignition switch. This electrical device secures the ignition and reads the anti-theft number inside your key.

The pins on the lock cylinder move up and downward to allow a mechanical key to be put in and turned. As time passes the pins can wear out (and even break) or become stuck. This prevents the key from turning and activating the vehicle. If you don't fix the issue, your vehicle may not start or even lock itself.

Fortunately the ignition cylinder can be repairable by a new one to allow your Vehicle locksmith to start. To do this, first disconnect the battery. The steering wheel trim needs to be removed in order to reach the ignition switch. Check the repair manual for the right instructions. The procedure may differ from model to model.

After the old cylinder has been removed, you'll have to purchase a replacement key that matches the key in your car ignition locked and follow the steps in the repair manual to put it in. It's a good idea test your new key prior to you complete.

The first indication of a malfunctioning ignition cylinder is the difficulty in starting your vehicle. The key might be difficult to insert or turn, and may require it to be moved around to make it move. It could be difficult to remove the key. This could be a sign that it is bent or worn out and is in need to be replaced.

It is convenient to have a Wrench mobile technician visit your workplace or home to provide a quick and reliable auto repair ignition lock cylinder of the ignition lock cylinder. This way, you don't need to take the car to a shop. We'll get you back on the road in no time by providing professional repairs and a fast, easy estimate.

Installing the New Switch

The ignition switch can malfunction in time. This can cause a range of issues, such as your car not starting, or the check engine light coming on. If you suspect your ignition switch is malfunctioning it is important to replace it before the issue becomes worse.

Based on the make and model of your vehicle, you may need to remove the covers or panels to access the ignition switch. If you do, carefully disconnect the electrical connectors from the switch and then remove any bolts or screws holding it in the position. Install the new switch after you have removed the old one. Once the switch is in place connect the wire and test it.

Before you install the new switch, ensure that it's on the off position. You may also have to reset the security system, especially if you're replacing the lock cylinder. Depending on your vehicle the procedure can be complicated and may require specialized tools.

Reinstall the panels or covers that you have removed, and connect the battery. Make sure you have the proper ignition switch replacement for your vehicle. You can find the correct switch by entering your year, make and model on the AutoZone search bar. The site will provide you with the list of ignition switches that are compatible with your car ignition switch repair and have the correct part number.

The ignition switch is essential for the operation of your vehicle, no matter if you're using an ignition cylinder lock repair key or a push-button start system. But it's also an extremely delicate and delicately constructed part that may wear out over time due to normal use or environmental factors. The weight of keys can make the switch squeak when it is inserted. Additionally, extreme temperature fluctuations can affect the lubricants and materials within. You should replace your switch as soon as it becomes damaged to ensure the safety and security of your vehicle.

It is a good idea to hire a professional to replace your ignition switch. This will ensure that the new switch is compatible with the existing key and that all of the connections are secure. This will help you to avoid costly mistakes that could damage your vehicle or cause problems with the new ignition.