• 목록
• 답변
• 게시판 리스트 옵션
  • 수정
  • 삭제

Glass Window Repair

Professional window repairmen work from high above the ground, navigating huge panes of glass. They work in extreme conditions and follow strict safety protocols.

Wearing protective clothing, remove all glazing putty and metal glazing points using a utility knife. A heat gun will help to soften and eliminate the old putty.

Replacement

If a window pane is broken, it may be tempting to repair the glass rather than replace it. It is more cost-effective to replace a window and it will also help to avoid other issues in your home's efficiency. It is also important to consider the type of glass that is broken to determine if this is a temporary fix or if you'll need to invest in an alternative that is more durable.

The first step to repair a broken window is to remove the sash, or frame and lay it flat on a table. Wearing eye protection, gently move the window's frame and then remove any remaining fragments. Then, use a utility knife to peel off the glazing compound as well as the glazing points that hold the glass in place. Make sure you keep the track of the location of these components to ensure that they can be reinstalled later.

After the frame and sash are removed and the frame is removed, you can begin preparation to install the new glass. Before doing this, make sure that the opening in the frame is size for the replacement window. To allow for frame and glass expansion and contraction to both directions, measure the opening and subtract 1/8 inch. Then, purchase double-strength glass cut to these exact dimensions. It is a good idea to also purchase enough glazier's clips, or points to install every 6 inches around each window pane.

Based on the window's warranty the window may be covered by the manufacturer and in this case, you must contact the company to file a claim. Once the new glass is installed, it needs to be sprayed with a thin coating of glazier's compound. After drying the compound and dry, you can paint it to match the rest of the window frame.

If your crack is more than an inch you can stop it from expanding by slicing the crack with a small arc, just above the crack. This trick is not foolproof but it can slow the development of the crack until you are able to take permanent measures.

Repair

Professional window contractors are equipped with the appropriate tools and know how to work with different kinds of glass. They know how to dispose of waste properly and are therefore less likely than other contractors to leave behind scraps that could inflict harm on family pets or family members. They are also familiar with working with various types of windows and could be able to spot issues that a novice home owner would not notice.

Before you begin the process of repairing cracked window glass, ensure to wear safety goggles and gloves. Even a tiny crack can cause shards of glass to fly away and could pose a danger to anyone in or around the home. It's also crucial to figure out what caused the crack in the first place, so that it can help prevent future issues.

Make a two-part mix of epoxy. They typically are made up of a 50/50 mix of hardener and resin. They must be mixed quickly. Once the mixture is ready, apply it to the glass crack and let it dry. It will take just about a minute however it is important to do it quickly because the mixture is extremely thick and fast drying.

Once the epoxy has dried, you can take off excess epoxy with a putty blade. You'll need to clean around the cracked glass. If you don't clean the area correctly the debris could cause further damage to the glass. Make use of a putty knife to smooth out the compound around the edge of your window and then match it to the wood frame.

To make a more durable option you can consider using a plastic cover. You can cover the glass using masking tape or a sturdy trash bag. This will prevent the crack from expanding, and will also keep out water, wind, bugs, and debris.

You can create a temporary fix if you are unable to get to the window in time. Simply run a bead of the material around the outside edge of the broken upvc window repairs. It won't completely fill the gap between frame and glass but it will help keep the break in place while you fix it.

Repainting

If your windows with glass are old, you may consider repainting them. This is an affordable alternative to replacing windows, and can give your home a new look. Make sure that the surface is clean before painting. Use rubbing alcohol or soap and water to get rid of oil smudges and other traces of dirt that can hinder paint from adhering. Wear rubber gloves when working on glass surfaces to avoid the transfer of oils from your hands onto the surface. In the end, you should apply several thin coats of paint instead of a single thick layer. This will make the paint last longer, and keep your windows looking even and smooth.

Make sure you have the right tools in your arsenal if you plan to repaint glass windows. You will need either a brush or sponge painter's tap as well as a ruler and toothpicks. It is also recommended to have the brushes and paint you'll be using for the project on hand. Be sure to adhere to the manufacturer's guidelines and be prepared with plenty of patience as it can take some time for the paint to dry.

If you are using solvent-based paint, you should also ensure that the space in which you work is well ventilated. This will reduce the chance of breathing into harmful chemicals and allow the paint to dry quicker. Also, make sure you have a protective mask for any spray paints you use.

For older glass windows, you'll need to prepare the surface prior to painting. Make use of soap and warm water to thoroughly clean the glass window. Then, use rubbing alcohol on any oil or grease remnants that may hinder the paint's adhesion. Make sure the windows are dry before you start coating them.

If your glass windows are energy efficient dual pane windows, then you might be able to file a claim with the dealer or window company that sold them to pay any repair or replacement costs. This is especially true if the windows are still under warranty and have experienced several problems with condensation or broken glass.

Sealing

Whether you have old double-pane windows with a broken seal or a newer version of insulated glass units (IGUs) that have experienced defogging, there are several methods to address the issue. The most expensive option is to replace the frame and insulated unit but it may be necessary if condensation or fog is causing energy loss. Other options include replacing the IGU with a single pane or fixing it by drilling a small hole into the bottom of the unit and then filling the solution with anti-fog.

You can also close the gap between a window frame and a threshold or sill by using a felt strip, or vinyl v-strip. Felt is inexpensive and can be fixed by gluing, nailing or stapled in place, but it does not provide much protection from moisture. Vinyl weather stripping v-strip is durable and easy to install however, it can be costly and is typically used for areas that are subject to abrasions that are high. Door sweeps are cheap and can be fixed to the floor but they create little to no barrier between the threshold or sill and air, dust, and debris.

To fix a cracked window seal first, you must employ a putty knife to remove the old caulk. Wearing eye protection and gloves take care to remove the glazing points -- tiny fasteners that fix the glass to the frame's recess, with sharp edges and pointed edges. After getting rid of the glazing points clean the grooves and sand the wood. Wipe away any sanding sludge then seal the wood surface using a linseed oil-based paint or clear sealer.

A caulking knife or putty can be used to apply traditional glazing putty, but a knife will provide an easier application and a stronger seal. Choose a putty that is specifically designed for glass windows as it will have higher adhesion and long-lasting.

Apply a small amount of the putty to the inner edge of the frame where it meets the glass. Slide the window into the frame so that the cut line on the glass lines up with the edge of the frame. Apply pressure to the glass to force the putty and create an elongated seal. Smooth the compound using a gloved finger and then wipe off any mistakenly applied caulk or drips that have escaped before it dries.